Benchables!

Jessica Daniels, owner operator of A Flair for Hair Salon in Milledgeville, Georgia whom is hosting the Charity auction at the Deep Roots Festival for two local ladies dealing with breast cancer and Hodgkin's lymphoma called and asked for more benches for the food court/eating area of the festival.

Kevin took stock again of his supplies and tools and went to work. His engineering background in manufacturing and design he put together a method of building them quickly but efficiently.

Once again using fall off wood from the sawmill, he found and inspiration in a long slice of trunk.  Leveling the piece on the sawmill he drilled 2-inch holes of deliberate spacing into them.

Then using a pipe threader machine he absconded from the local dump not long ago, he built a bit out of 2-inch pipe with teeth ground out using his angle grinder.   Giant toothpicks skinned and whittled down from a tree that didn't make it through a recent storm would become the legs. 

Arthur coined the name Benchables because they are suited for use as both benches and tables on a picnic table theme.

They run 4 feet in average length and range from 11 to 16 inches wide.

~Cheryl

Check them out at the Festival..............possible auction items........... !

End of Trail - Line Shack Benches

Along the original Cowboy trails, Kevin revisits the old west, dropping in on his StickStoneSteel genre to bring to life some old standards.

These Line Shack Benches are reminiscent of what the Cowhands may have built for the months they spent away from the ranch tending to cattle in the high pastures.

Kevin’s great Uncle migrated from Prussia to homesteaded in the Dakota Territory. His sons completed such tasks including the fencing and furnishing of the bunkhouses and what not.

Bow Saws, 1 and 2 man saws, an ax, a forge and hammers were among the tools that made the initial trip along side food staples, cookware and clothing. Then using what wood was left over from building fences and their housing, they put together a few luxuries. Tables and benches which would remain on site long after the cattle tending tour of duty was complete, set up for seasons to follow.

Now Kevin’s tools are electric and more calculating, but he builds in their spirit of making use of what is available. Where the Cowhands most likely used an old horseshoe Kevin uses scrap iron and saw blades.

The benches seen here are made from pine slabs, scrap iron and used saw blades cut and forged to fit the design. They are a bit upscale from what their ancestors looked like, complemented with stain washes and readymade bolts from an old futon frame but they do inspire a campfire cookout.

Come sit a spell. 

These benches will be on site at the "Deep Roots Festival" in Milledgeville,  Georgia on Saturday October 22nd.   

We owe thanks for this opportunity to Jessica Danials, owner operator of A Flair for Hair Salon here in Milledgeville,  whom is hosting the Charity auction at this festival for two local ladies dealing with breast cancer and Hodgkin's lymphoma.

~Cheryl

P.s. These are prototype pieces, 76 inches long, 17 inches in height with a bench width of 15 inches. What would you pay for something like this?

Possible options are cushioned, and different ranges of finishes, you tell us, and we’ll go from there…

Sunburst Table - StickStoneSteel 1st Appearance!

Recently one of our previous clients asked told us about a non-profit charity auction she is holding to benefit for two women; one dealing with breast cancer and the other hodgkin’s lymphoma. She asked Kevin if he would donate some of what she calls his ‘rustic’ hand made furniture for the cause. He happily complied. 

She then asked if he could supply benches and tables for the food court seating of the Deep Roots Festival, Milledgeville, Georgia where her auction will take place.

With less than a month to go, Kevin plunged into his "StickStoneSteel" mode.  Between the Saw Mill fall off and the collection of items collected and obtained over time his palate was already full.

He’d already been playing with forge bending steel for benches for our own deck so Naturally while his mind clicked away at designs for benches made out of fall off wood he came into the house and asked me for whatever poster paint Arthur had left over in the craft cupboard.

Within in minutes, under the carport he had a concrete garden walk paver balancing on a couple bags of concrete and was joyfully painting away like a happy kid. 

With limited colors, he went freewheeling; digging at the bottom of the bottles where the thick colored gook had accumulated. He managed to scrape more than enough yellow for the center.  I watched him artfully dash out orange and red rays from that yellow core.  I am pretty sure he was fighting the urge to unleash a wild splattering of paint at it but refrained.

Hours later, after the paint had dried he brought the stand to the house.  Chain welded together for the tripod legs with a used saw blade to secure the balance. What you can’t see from this picture is an old grinding wheel holding the concert paper in place with a heavy nut and bolt.

Arthur has made a request that Kevin build one like this for his room.  I want one too!   Guess we’ll have to get more poster paint.  :)

~Cheryl

Celtic Propane Tank Bell

"Made from an old Propane Tank,Gloss black paint and with the red I've garnished it with a hand designed Celtic Weave. I am unsure of the proper term, but the 'banger' is made of pine. Sounds nice." - KR

Check out Kevin's new Etsy page:

http://www.etsy.com/people/KevinGoingGreen

And, we're waiting to hear from you..........I know you've got DIY dreams.............

~ Cheryl